Differences

This shows you the differences between two versions of the page.

--- equipment:handling [2012/01/29 18:53] – mcmaster
+++ equipment:handling [2013/11/10 23:10] (current) – mcmaster
@@ Line 3: / Line 3: @@
 ====== Metal tweezers ======
-Do not use metal tweezers to handle dies.  It is very easy to apply too much pressure and chip dies.
+{{gallery>:mcmaster:tweezers:metal_set.jpg}}
+**Do not use metal tweezers to handle dies.**  It is very easy to apply too much pressure and chip dies.
 ====== Carbon fiber tweezers ======
+{{gallery>:mcmaster:tweezers:lindstrom_tl_253-sa.jpg}}
 Preferred method used by cleanrooms.  These are unfortunately the most expensive as well.  on eBay you can pick up a pair for $15.  Typically they have a metal body and a (screwed on) carbon fiber tip.
 WARNING: these are epoxy / resin filled.  Do not expect them to be resistant to acids and be wary of acetone.  (as I realized the hard way...)
+Trim brand Carbon Tip Pointed Tweezers are an inexpensive brand intended for hair removal.  They don't have a sharp tip but work well enough for general handling.  I got them when they were cheap on eBay but still can be found around ([[http://www.ixir.co.uk/products/Trim-Carbon-Tip-Pointed-Eyebrow-Tweezers.html|example]])
+  * $5 each + $5 S/H: http://www.amazon.com/Trim-Precision-Deluxe-Carbon-Tweezers/dp/B00BS15UNW
 Advantages
@@ Line 38: / Line 46: @@
 ==== 9330X ====
-These are very common on eBay.  They come in a few different sizes and sell for something around 2 / 2$.  They have a large mixed particle content (glass and ?) which makes them somewhat resistant to acetone.
+{{gallery>:mcmaster:tweezers:9330x.jpg}}
+These are very common on eBay.  They come in a few different sizes and sell for something around 2 / 2$.  They have a large mixed particle content (glass and ?) which makes them somewhat resistant to acetone.  Here is a pair that was in acetone for a short period of time:
+{{gallery>:mcmaster:tweezers:9330x_acetone.jpg}}
+It will leave black streaks when wiped after exposure.  Additionally it will flake off particulates which is bad for keeping dies clean.
 Example models:
@@ Line 44: / Line 58: @@
   * 93302: the tip is longer than the 93307 but otherwise identical (other than the number)
-==== Jameco antistatic tweezer set ====
+tip top, 93302 tip bottom:
+{{gallery>:mcmaster:tweezers:9330x_tip.jpg}}
+==== ProsKit ====
+{{gallery>:mcmaster:tweezers:prokit_set.jpg}}
+I got these as a Jameco antistatic tweezer set.
+This seems to have good resistance against acetone.  Here is a well used tweezer:
+{{gallery>:mcmaster:tweezers:prokit_used.jpg}}
+Although its dirty its still in very good shape.  Getting it wet with acetone and wiping it doesn't leave a black streak.
+Advantages:
+  * Good chemical resistance
+  * Soft against dies
+Disadvantages:
+  * More expensive than other brands
+====== Tweezers ======
+Tweezers are often useful for several purposes including picking dies out of chemical solutions (acid, acetone), plucking bond wires, and general handling. Each has its own issues that make different kinds of tweezers useful.
+====== General handling ======
+Plastic tweezers are preferred as they tend to cause less damage.
+====== Plucking ======
+Hold the die with those described in "general handling." If you are plucking by knocking wires off, definitely go with plastic. If you are coordinated, metal tweezers are preferred for normal plucking. Otherwise, go with plastic if you think you might slip and hit the die. It won't grip as well and will probably degrade much faster, but will be safer for the die.
-This seems to have good resistance against acetone.  It is unfortunately, more expensive than other brands.
+====== Acetone ======
+Useful for pulling dies out of rinse solutions. Some tweezers are resistant, others aren't. Wet a paper towel with acetone and try rubbing the upper area of the tweezers. If plastic comes off, its no go.
+TODO: get a list of some known acetone resistant tweezers.
+====== Nitric acid ======
+Plastic aluminium, or stainless tweezers. Unknown if any plastics react with nitric? If you need to pull it out of hot acid, definitely go with aluminium. Stainless is also pretty resistant to nitric acid.
+====== Sulphuric acid ======
+Plastic (or maybe stainless?) tweezers.