Differences

This shows you the differences between two versions of the page.

--- fet:start [2016/01/03 06:27] – created mcmaster
+++ fet:start [2016/01/03 06:44] (current) – removed mcmaster
@@ Line 1: / Line 1: @@
-====== MOSFET theory 101 ======
-Pure silicon is a mediocre conductor but when its doped (either positive "p" or negative "n") it becomes much more conductive.  One simple application of this is to make a diode by placing n doped silicon next to p doped silicon.  These charges cancel out and leave a poorly conducting charge neutral area in the middle.  By applying positive voltage to the positive p side and negative voltage to the negative n side, the like charges repel and push the charge neutral area closer.  As voltage is increased the neutral area shrinks and allows current to flow freely.  Note that iss also possible to get current to flow in the other direction by applying a high voltage (avalanche effect) but this is not used in digital logic.
-MOSFETs build on diodes by adding a control terminal to adjust charge between two similarly doped areas.  For example, when positive voltage is applied to the gate of a N MOSFET it conducts.  Similarly, when a negative voltage is applied to the gate of a P MOSFET it conducts.  While real devices have many other critical details, this is generally sufficient detail to reverse engineer digital logic: while a logic designer has to make the system work reliably, a reverse engineer generally assumes the system works reliably.
-{{:wiki:mosfets.png|}}
-This ([[http://en.wikipedia.org/wiki/MOSFET|Wiki]]) image shows schematic symbols for different types of MOSFETs.  When analyzing basic CMOS circuits only N MOSFETs (NFETs) and P MOSFETs (PFETs) are relevant.  However, NMOS and PMOS also use depletion mode transistors.  For most practical purposes, they can be inferred as resistors and the device physics can be ignored.
-A note of caution: chip designers know this is how people think when they try to copy chips.  They occasionally exploit real device physics even in digital logic to confuse reverse engineers ("traps").  For the meantime assume that circuits work as described above but be mindful that there are exceptions.
-====== MOSFET layout 101 ======
-But what are those funny triangles next to some of them?  Lets go a little deeper.  This is a typical cross section ([[http://en.wikipedia.org/wiki/File:MOSFET_functioning.svg|derivative work]]) of an N MOSFET:
-{{:wiki:mosfet_functioning_modified.png|}}
-Specifically it represents this schematic symbol ([[http://en.wikipedia.org/wiki/File:IGFET_N-Ch_Enh_Labelled.svg|source]]):
-{{:wiki:igfet_n-ch_enh_labelled.png|}}
-Now we can understand that that triangle is a diode notation.  In an N MOSFET, the source is N doped sitting in a P well.  Thus the body forms a PN junction with the source and drain, connected in the middle of the channel.  That is, applying a positive voltage to the body will conduct out either the source or drain.  If the body is left unconnected it can generate some stray currents.  By connecting the body to ground it reverse biases the PN junctions (particularly the body-drain) and helps prevent leakage as well as potential latchup conditions.
-To make the final point, the "no bulk" version above is a discrete MOSFET.  Since it isn't made in a well process there's no reason to have a P substrate.  For example, it might simply be an N wafer with P doping just in the channel region  (TODO: get some discrete MOSFET pictures.  Maybe bad example due to self aligned gate practices).
-{{gallery>:mcmaster:n_fet_no_metal.png}}
-Typical poly gate transistor from a typical standard cell based IC.  Some of the contact metal can be seen on the bottom but the gate itself is poly.
-====== Gate ======
-In general, there are three types of FET technology (in chronological order):
-  * Early aluminum metal gate
-  * Polysilicon gate
-  * Metal gate w/ high-k dielectric
-Within each of these, especially polysilicon gates, there are many variations.
-====== Metal Oxide Semiconductor Field Effect Transistor (MOSFET) ======
-Dominant type seen today. Original ones were true metal gate on an oxide as the name implies, but modern ones tend to use polysilicon instead.
-{{:image:fairchild_4011_transistor.jpg?300}}
-Above: classical metal gate type. From left to right: source, gate, drain. Note that gate and drain are more or less identical in CMOS.  Colors are from thin film interference indicating different layer thicknesses.
-{{:image:CMOS_metal_gate_transistor_no_metal.jpg?300}}
-Above: now metal removed.  Black gate area is probably salt from dissolved gate metal.  Color difference is because its from a different chip, not etch process (although etching can also change color)
-===== Gate: early metal =====
-==== MOS MPS7083 ====
-{{:mcmaster:mos:mps7083:q_mz.jpg?300}}
-{{:mcmaster:mos:mps7083:q_dlyr1.jpg?300}}
-Above top: top metal.  Bottom: Al and some SiO2 removed
-Typical metal gate CMOS transistor as used in non-trivial chips (ie CPU).  The control signal
-==== Fairchild CD4011 ====
-{{:image:fairchild_4011_transistor.jpg?300}}
-{{:image:cmos_metal_gate_transistor_no_metal.jpg?300}}
-Above  textbook style metal gate transistors
-==== CMOS quiz ====
-{{:quiz:metal_gate_cmos:q.jpg?300}}
-See quiz for analysis