Introduction to screens (ref):

• standard
  • slow
  • calcium tungstate
• rare earth
  • fast
  • gadolinium or lanthanum
  • Commercial brands: Kodak Lanex

There's a good vendor summary / cross reference chart here: http://www.mcio.com/Products/comparison-chart.aspx

I think the number following the name is generally the gain. That is a 400 screen will put out twice as much light per x-ray as a 200 screen They call this the “speed” presumably because it makes film expose faster. Chart here

Brands:

• 3M
• AGFA
• DUPONT/STERLING
• FUJI
• JPI
• KIRAN
• KODAK
  • Lanex: rare earth green
• KONICA
• MCI OPTONIX

Following sections are for screens I own. Basically they were cheap on eBay

Image	Vendor	Product	Phosphor	Speed	Size	kV sensitivity	Labels	Notes
	Kodak	Lanex X-OMAT Fine	Green rare earth	100			EXTREMITY Tube Side Kodak cassette Kodak Lanex Fine Screens KODAK X-OMAT Cassette Made in the U.S.A. by EASTMAN KODAK COMPANY Rochester, New York 14650 TM: Kodak, Lanex, X-Omat KP 115179 KODAK LANEX FINE 1261004232CA#9341
	Kiran	KG4	Green rare earth	400			SKU: JV-NIC-B-KIRACASE Date: 1/30/12 BIN: Kiran 8“x12” KG4 Medical Hospical X-Ray Hard Case Intensifying Screen Cassette Kiran Intensifying Screens Date Installed: 12/05 Screen Type: KG4 Date Last Cleaned: KG4 825234
	Dupont	Cronex Quanta Detail	Blue rare erath	100	7“x17”		EXTREMITY CASSETTE 18×43 cm. (7 x 17 in.) LETTER NO. 8 SCREEN NO. DATE CLEANED: 7-20-98 BY: FM 11382 DUPONT CRONEX INTENSIFYING SCREENS QUANTA DETAIL DUPONT QUANTA DETAIL-T J1 3CCC24

was offered a broken tube but I don't think it would have been useful

Ben K x-ray, CBCT “chicken” setup

• originally unshielded but I think is now?
• In CBCT mode runs automatically via arduino and thus person doesn't have to get exposed

Russian fellow: http://habrahabr.ru/post/254015/

• …who gave himself acute radiation sickness. A stern warning to those not taking such a setup seriously

John M dental x-ray setup

• which has about 100 lbs of lead shielding
• also operated remotely via ssh to laptop

Goal: stop using my Sherline rotary stage and instead use spare CNC rotary stage (from laser machine purchase lot)

Motor: Vexta PH566-B 5 phase stepper

Controller: Rorze RD-053MS

• Datasheet] * [[http://www.rorze.com/english/Tech/controll/RD053MS.pdf|Spec sheet
• Has a lot of pins labeled
• Enclosed in box with cable running to the rotary table
• 3 per box
• Need to interface to output Centronix connector

The left side connections are pretty obvious:

• power
  • 18V to 40VDC
• motor phases

Left side less so

• diff1
• diff2
• 4P IN
• FREE
• PHASE OUT
• ALARM OUT

Summary

• Up to 400 microsteps/step
• Current driven…looks like approx. 3.8mA at 5VDC?
• 3.3V compatible?

Two ways that step/direction can be configured

Two Clock Input (2CK) (Inputs two clock pulses - CW clock pulse and CCW clock pulse)

• CW+/-: Motor rotates in CW direction with a pulse current of 8 to 20mA from CW+ to CW- terminal.
• CCW+/-: Motor rotates in CCW direction with a pulse current of 8 to 20mA from CCW+ to CCW- terminal.

One Clock Input (1CK) (Inputs clock pulse and direction (CW, CCW))

• CLK+/-: Motor rotates in CW direction with a pulse current of 8 to 20mA from CLK+ to CLK- terminal and UD input off.
• UD+/-: Motor rotates in CCW direction with a pulse current of 8 to 20mA from CLK+ to CLK- terminal and UD input turned ON.

Basically it looks like second is standard step/direction configuration

• Yep buried in later documentation: Selects clock input, Two clock input method (2CK) or Pulse & Direction input method (1CK).

6-2 Full Step Input (4P IN +/-): Motor rotates in full step mode with a pulse current of 2 to 10mA (approx. 3.8mA at 5VDC) from “4P IN +” to “4P IN –”

6-3 Free Input (FREE +/-): The excitation current of motor will become 0 and a motor can be rotated by hand with a pulse current of 2 to 10mA (approx. 3.8mA at 5VDC) from “FREE+” to “FREE-”.

• NOTE: Do not turn this input ON when motor is running at high speed, this operation would

damage the amplifier circuits.

6-4 Phase Output (PHASE OUT+/-): PHASE OUT output (open collector output) is turned ON at the phase home. One pulse is put out every time the motor moves 7.2゚ in case of 0.72゚ motor. The Duty of output ON is 10%.

6-5 Alarm Output (ALARM OUT+/-): Overheating protection circuit intervenes turning ALARM output ON. (Open collector output ON)

All channels as given are configured the same

• 8-1 current range: 1.5A
• 8-2 clock select: 1 clock
• 8-3 auto current down: on
• 8-4:8-8: microstepping: 32
  • D1: 0
  • D2: 1
  • D3: 0
  • D4: 0
  • D5: 1
  • 1: to the left, 0: to the right (assuming OFF ⇒ 0)

Agilent PS test on CLK input while off (assuming its just a PD)

• 0V 3 mA (subtracted from all other values)
• 3.3V: 7 mA
• 5V: 13 mA
  • They said 3.8 mA…are inputs non-uniform?
• 2 mA: 1.8 V
• 8 mA: 3.5 V
• 10 mA: 4.1 V
• 20 mA: 6.8 V

(note to self: script a curve tracer…)