This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| motor:stepper [2018/05/31 01:45] – [Gecko DB25 (multi-axis indexer)] mcmaster | motor:stepper [2018/12/26 15:20] (current) – removed mcmaster | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Place to aggregate motor information, | ||
| - | 2018-05-28: creating page to aggregate industry pinout information and mcmaster recommendations. | ||
| - | |||
| - | ====== Connector ====== | ||
| - | |||
| - | List of common connectors | ||
| - | |||
| - | |||
| - | ===== DB25 (step/ | ||
| - | |||
| - | {{: | ||
| - | |||
| - | Above: Compumotor OEM650 pinout | ||
| - | |||
| - | {{: | ||
| - | |||
| - | Above: PMC VS Drive pinout | ||
| - | |||
| - | This seems to have been a de facto standard for some years. I've observed it on Compumotor, PMC, and other drivers. | ||
| - | |||
| - | mcmaster: IMHO this is too bulky to use in modern applications, | ||
| - | |||
| - | |||
| - | ===== DB9 (step/ | ||
| - | |||
| - | Seen on Gecko drivers. I've not seen it elsewhere, but the Gecko is pretty popular | ||
| - | |||
| - | |||
| - | ===== IDC 5x2 (step/ | ||
| - | |||
| - | Used on some MDrive17 motors | ||
| - | |||
| - | mcmaster: of particular interest to me since I try to use these motors by default. | ||
| - | |||
| - | |||
| - | ===== M12 connector (power + CAN) ===== | ||
| - | |||
| - | M12/M23 seems to be common on modern stepper motors. The MDrive manual for example cites it was done to reach IP65 enclosure rating: | ||
| - | |||
| - | < | ||
| - | The MDrive17Plus2-65 Motion Control adds protection against the ingress of fluids and dust to | ||
| - | the MDrive17Plus2 by changing the motor-drive enclosure to meet IP65 specifications. With this | ||
| - | change the connector configuration changes to industry standard M12/M23 circular connectors. | ||
| - | </ | ||
| - | |||
| - | http:// | ||
| - | * A-coding: actuator-sensor plug connections for DeviceNet, IO link and Profibus | ||
| - | * DeviceNet is used my mcmaster MFCs | ||
| - | * B-coding: Fieldbus connections for Profibus and Interbus | ||
| - | * D-coding: Industrial Ethernet, Profinet, Ethernet/IP and EtherCat | ||
| - | * S-coding: Motor, Frequency-convertors, | ||
| - | * T-coding: Fieldbus comp, passive distribution boxes, motors, PSUs for Power, 63V, 12A | ||
| - | |||
| - | |||
| - | ===== Combicon 5 pin (bipolar motor) ===== | ||
| - | |||
| - | {{: | ||
| - | |||
| - | Above: PMC motor | ||
| - | |||
| - | ===== Gecko DB9 (bipolar motor) ===== | ||
| - | |||
| - | {{: | ||
| - | |||
| - | ===== Gecko DB25 (multi-axis indexer) ===== | ||
| - | |||
| - | {{: | ||